legacycentral bbs

ok i did some figureing and calling around so bear with me.. and figure you
own math..

I measured my 91 LS WGN's hood, Front fenders, Front & Rear Bumpers.

The Hood measured out to about: 8'.3" sq Ft.
the mold would cost $255.00 and the part would cost $64.00 (rounded up)

The Fender measured out to about 6'.3" sq Ft
the mold would cost $189.00 and the part would cost $47.50 (rounded up)

The Front Bumper measured out to about 8'.1" sq Ft
The mold would cost $243.00 and the part would cost $60.75 (rounded up)

The Rear Bumper measured out to about 9'.1" sq Ft
The mold would cost $273.00 and the part would cost $68.25 (rounded up)

The Part price is under the assumption that the mold already exsists.. Which
it dosen't..

Group Prices.

First i called around for a turbo Hood it came to $320.00 and then i priced
an RS bumper which came to $249.00, the Scoupe came to about $90, and they
couldn't find the price for the vents these prices were obtained from Macco,
an autobody shop for those not in the US.

The following group price is for the Turbo Hood with holes cut and under the
assumption that a Turbo hood will be needed to be purchaced to make the mold.
these prices were also made with the value that a min of 5 people were going
in on it. the price will be higher is less come in on the deal and less if
more than 5 people come in on the deal. these prices are not includeing any
modifications (hood scoup/flares/etc..)

TurboHood :+320.00
Mold: +255.00
Part + 64.00
Part + 64.00
Part + 64.00
Part + 64.00
Part + 64.00
------------------------------------
Total: =895.00
Split 5 ways: 179.00
Price if hood is donated or is available for free: 155.00

The fender is easy as i can use my fenders for the molds

Mold: +189.00
Part: + 47.50
Part: + 47.50
Part: + 47.50
Part: + 47.50
Part: + 47.50
-----------------------------
Total: =426.50
Split 5 ways : $85.30

Front bumper is figured with my bumper and not the RS as i do not own an RS
bumper to measure..

Mold : +243.00
Part: + 60.75
Part: + 60.75
Part: + 60.75
Part: + 60.75
Part: + 60.75
---------------------------
total: =546.75
add :249.00 for RS bumper and divide by 5 for apoxamate price for RS legacy
bumper
Split 5 ways : $109.35

Rear bumper is off of my WGN

Mold: +273.00
Part: + 68.25
Part: + 68.25
Part: + 68.25
Part: + 68.25
Part: + 68.25
----------------------------
Total: = $614.25
Split 5 ways : $122.85

Any Donated Part will be shipped back at my own expence. So you will get your
originals back. Otherwise UPS charges will apply. if there is a specific year
a couple of you want i will call Macco and find out how much the hood costs
and add it to the price and after the mold is made return the hood and refund
that money between the partys involved..

David Carter

P.S this has been forwaded to the STI list from the legacy list for all those
that might be interested...


To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

Dave,

You might want to make a post on the i-club forum as well. Club buys there have been known to draw over a dozen people easy but this is a special situation b/c we are only talking BC-BF parts here.

Just a thought.

-Sambo

-----Original Message-----
From: bussaca2@aol.com [mailto:bussaca2@aol.com]
Sent: Tuesday, October 03, 2000 42 PM
To: BC-BFLegacyWorks@egroups.com
Cc: STi_Mlist@imprezawrx.org
Subject: [BC-BFLegacyWorks] FIBERGLASS PARTS GROUP PRICES>


ok i did some figureing and calling around so bear with me.. and figure you
own math..

I measured my 91 LS WGN's hood, Front fenders, Front & Rear Bumpers.

The Hood measured out to about: 8'.3" sq Ft.
the mold would cost $255.00 and the part would cost $64.00 (rounded up)

The Fender measured out to about 6'.3" sq Ft
the mold would cost $189.00 and the part would cost $47.50 (rounded up)

The Front Bumper measured out to about 8'.1" sq Ft
The mold would cost $243.00 and the part would cost $60.75 (rounded up)

The Rear Bumper measured out to about 9'.1" sq Ft
The mold would cost $273.00 and the part would cost $68.25 (rounded up)

The Part price is under the assumption that the mold already exsists.. Which
it dosen't..

Group Prices.

First i called around for a turbo Hood it came to $320.00 and then i priced
an RS bumper which came to $249.00, the Scoupe came to about $90, and they
couldn't find the price for the vents these prices were obtained from Macco,
an autobody shop for those not in the US.

The following group price is for the Turbo Hood with holes cut and under the
assumption that a Turbo hood will be needed to be purchaced to make the mold.
these prices were also made with the value that a min of 5 people were going
in on it. the price will be higher is less come in on the deal and less if
more than 5 people come in on the deal. these prices are not includeing any
modifications (hood scoup/flares/etc..)

TurboHood :+320.00
Mold: +255.00
Part + 64.00
Part + 64.00
Part + 64.00
Part + 64.00
Part + 64.00
------------------------------------
Total: =895.00
Split 5 ways: 179.00
Price if hood is donated or is available for free: 155.00

The fender is easy as i can use my fenders for the molds

Mold: +189.00
Part: + 47.50
Part: + 47.50
Part: + 47.50
Part: + 47.50
Part: + 47.50
-----------------------------
Total: =426.50
Split 5 ways : $85.30

Front bumper is figured with my bumper and not the RS as i do not own an RS
bumper to measure..

Mold : +243.00
Part: + 60.75
Part: + 60.75
Part: + 60.75
Part: + 60.75
Part: + 60.75
---------------------------
total: =546.75
add :249.00 for RS bumper and divide by 5 for apoxamate price for RS legacy
bumper
Split 5 ways : $109.35

Rear bumper is off of my WGN

Mold: +273.00
Part: + 68.25
Part: + 68.25
Part: + 68.25
Part: + 68.25
Part: + 68.25
----------------------------
Total: = $614.25
Split 5 ways : $122.85

Any Donated Part will be shipped back at my own expence. So you will get your
originals back. Otherwise UPS charges will apply. if there is a specific year
a couple of you want i will call Macco and find out how much the hood costs
and add it to the price and after the mold is made return the hood and refund
that money between the partys involved..

David Carter

P.S this has been forwaded to the STI list from the legacy list for all those
that might be interested...


To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com





To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

In a message dated 10/3/00 7:26:42 PM Eastern Daylight Time, bussaca2@aol.com
writes:

<< TurboHood :+320.00
Mold: +255.00
Part + 64.00
Part + 64.00
Part + 64.00
Part + 64.00
Part + 64.00
------------------------------------
Total: =895.00
Split 5 ways: 179.00
Price if hood is donated or is available for free: 155.00 >>

I made a mistake :
Price if hood is donated or is available for free: 115.00

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

Do you need a hood to do this? Is that what you need? I would ship you mine but it has a frigging crease in it - no good for something like this. However, if we get desperate I could order one and send it to you, then return it for refund.

-Sambo

-----Original Message-----
From: bussaca2@aol.com [mailto:bussaca2@aol.com]
Sent: Tuesday, October 03, 2000 5:24 PM
To: BC-BFLegacyWorks@egroups.com
Subject: Re: [BC-BFLegacyWorks] FIBERGLASS PARTS GROUP PRICES>


In a message dated 10/3/00 7:26:42 PM Eastern Daylight Time, bussaca2@aol.com
writes:

<< TurboHood :+320.00
Mold: +255.00
Part + 64.00
Part + 64.00
Part + 64.00
Part + 64.00
Part + 64.00
------------------------------------
Total: =895.00
Split 5 ways: 179.00
Price if hood is donated or is available for free: 155.00 >>

I made a mistake :
Price if hood is donated or is available for free: 115.00

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com





To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

In a message dated 10/3/00 8:48:49 PM Eastern Daylight Time, samb@vitessa.net
writes:

<< Do you need a hood to do this? Is that what you need? I would ship you mine
but it has a frigging crease in it - no good for something like this.
However, if we get desperate I could order one and send it to you, then
return it for refund.

-Sambo >>
This is what i was going to do.. Buy a turbo hood for $320 ,have the mold
made, make the individual parts. and then return the hood and use the money
to ship the fiberglass hoods and split the remaining up between the partys
involved. thats why there are two diferent prices under the hood catagory.

Anyways i'm actually in the process of talking to someone about a Turbo-hood.

But any Donations of a loaner hood or other body part are welcome..

David Carter


To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

David

I would be very interested in a rs style bumper for my 92 turbo
sedan,but only if I would beable to mount a pair of either the cibie
or PIAA driving lights in the factory locations(factory being for the
impreza). Living in northern Minnesota/Wisconsin requires me to drive
on very dark, very deer infested roads and I want some added light.
The rs bumper would only help, giving the lights a more finished look
and a meaner apperance.

Jay


--- In BC-BFLegacyWorks@egroups.com, bussaca2@a... wrote:
> ok i did some figureing and calling around so bear with me.. and
figure you
> own math..
>
> I measured my 91 LS WGN's hood, Front fenders, Front & Rear Bumpers.
>
> The Hood measured out to about: 8'.3" sq Ft.
> the mold would cost $255.00 and the part would cost $64.00 (rounded
up)
>
> The Fender measured out to about 6'.3" sq Ft
> the mold would cost $189.00 and the part would cost $47.50 (rounded
up)
>
> The Front Bumper measured out to about 8'.1" sq Ft
> The mold would cost $243.00 and the part would cost $60.75 (rounded
up)
>
> The Rear Bumper measured out to about 9'.1" sq Ft
> The mold would cost $273.00 and the part would cost $68.25 (rounded
up)
>
> The Part price is under the assumption that the mold already
exsists.. Which
> it dosen't..
>
> Group Prices.
>
> First i called around for a turbo Hood it came to $320.00 and then
i
priced
> an RS bumper which came to $249.00, the Scoupe came to about $90,
and they
> couldn't find the price for the vents these prices were obtained
from Macco,
> an autobody shop for those not in the US.
>
> The following group price is for the Turbo Hood with holes cut and
under the
> assumption that a Turbo hood will be needed to be purchaced to make
the mold.
> these prices were also made with the value that a min of 5 people
were going
> in on it. the price will be higher is less come in on the deal and
less if
> more than 5 people come in on the deal. these prices are not
includeing any
> modifications (hood scoup/flares/etc..)
>
> TurboHood :+320.00
> Mold: +255.00
> Part + 64.00
> Part + 64.00
> Part + 64.00
> Part + 64.00
> Part + 64.00
> ------------------------------------
> Total: =895.00
> Split 5 ways: 179.00
> Price if hood is donated or is available for free: 155.00
>
> The fender is easy as i can use my fenders for the molds
>
> Mold: +189.00
> Part: + 47.50
> Part: + 47.50
> Part: + 47.50
> Part: + 47.50
> Part: + 47.50
> -----------------------------
> Total: =426.50
> Split 5 ways : $85.30
>
> Front bumper is figured with my bumper and not the RS as i do not
own an RS
> bumper to measure..
>
> Mold : +243.00
> Part: + 60.75
> Part: + 60.75
> Part: + 60.75
> Part: + 60.75
> Part: + 60.75
> ---------------------------
> total: =546.75
> add :249.00 for RS bumper and divide by 5 for apoxamate price for
RS
legacy
> bumper
> Split 5 ways : $109.35
>
> Rear bumper is off of my WGN
>
> Mold: +273.00
> Part: + 68.25
> Part: + 68.25
> Part: + 68.25
> Part: + 68.25
> Part: + 68.25
> ----------------------------
> Total: = $614.25
> Split 5 ways : $122.85
>
> Any Donated Part will be shipped back at my own expence. So you
will
get your
> originals back. Otherwise UPS charges will apply. if there is a
specific year
> a couple of you want i will call Macco and find out how much the
hood costs
> and add it to the price and after the mold is made return the hood
and refund
> that money between the partys involved..
>
> David Carter
>
> P.S this has been forwaded to the STI list from the legacy list for
all those
> that might be interested...


To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

In a message dated 10/3/00 11:26:53 PM Eastern Daylight Time,
legacy_productions@yahoo.com writes:

> David
>
> I would be very interested in a rs style bumper for my 92 turbo
> sedan,but only if I would beable to mount a pair of either the cibie
> or PIAA driving lights in the factory locations(factory being for the
> impreza).

that is egzactly what i'm tring to do.. i personaly wouldn't settle for less.


Living in northern Minnesota/Wisconsin requires me to drive
> on very dark, very deer infested roads and I want some added light.
> The rs bumper would only help, giving the lights a more finished look
> and a meaner apperance.
>

I totaly agree. i put you on the list ,Unless you really icthing for them
imediately I'm gonna wait till i got at least 5 other people who want the
same thing to keep your costs down.

David Carter

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

I can afford to wait. (poor college student talking)
Just tell me when you can get them.
--- bussaca2@aol.com wrote:
> In a message dated 10/3/00 11:26:53 PM Eastern
> Daylight Time,
> legacy_productions@yahoo.com writes:
>
> > David
> >
> > I would be very interested in a rs style bumper
> for my 92 turbo
> > sedan,but only if I would beable to mount a pair
> of either the cibie
> > or PIAA driving lights in the factory
> locations(factory being for the
> > impreza).
>
> that is egzactly what i'm tring to do.. i personaly
> wouldn't settle for less.
>
>
> Living in northern Minnesota/Wisconsin requires me
> to drive
> > on very dark, very deer infested roads and I want
> some added light.
> > The rs bumper would only help, giving the lights
> a more finished look
> > and a meaner apperance.
> >
>
> I totaly agree. i put you on the list ,Unless you
> really icthing for them
> imediately I'm gonna wait till i got at least 5
> other people who want the
> same thing to keep your costs down.
>
> David Carter
>


__________________________________________________
Do You Yahoo!?
Yahoo! Photos - 35mm Quality Prints, Now Get 15 Free!
http://photos.yahoo.com/

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

same here....I hear ya...hopefully not too much longer though

************************
Josh Colombo
jcc189@psu.edu <mailto:jcc189@psu.edu>
************************



-----Original Message-----
From: Jay Erlenbach [mailto:legacy_productions@yahoo.com]
Sent: Wednesday, October 04, 2000 12:14 AM
To: BC-BFLegacyWorks@egroups.com
Subject: Re: [BC-BFLegacyWorks] Re: FIBERGLASS PARTS GROUP PRICES>


I can afford to wait. (poor college student talking)
Just tell me when you can get them.
--- bussaca2@aol.com wrote:
> In a message dated 10/3/00 11:26:53 PM Eastern
> Daylight Time,
> legacy_productions@yahoo.com writes:
>
> > David
> >
> > I would be very interested in a rs style bumper
> for my 92 turbo
> > sedan,but only if I would beable to mount a pair
> of either the cibie
> > or PIAA driving lights in the factory
> locations(factory being for the
> > impreza).
>
> that is egzactly what i'm tring to do.. i personaly
> wouldn't settle for less.
>
>
> Living in northern Minnesota/Wisconsin requires me
> to drive
> > on very dark, very deer infested roads and I want
> some added light.
> > The rs bumper would only help, giving the lights
> a more finished look
> > and a meaner apperance.
> >
>
> I totaly agree. i put you on the list ,Unless you
> really icthing for them
> imediately I'm gonna wait till i got at least 5
> other people who want the
> same thing to keep your costs down.
>
> David Carter
>


__________________________________________________
Do You Yahoo!?
Yahoo! Photos - 35mm Quality Prints, Now Get 15 Free!
http://photos.yahoo.com/

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com





To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

Jeez!! I can't keep up with you guys! Ok, so I'm interested in this fiberglass
hood and front bumper deal. Is there anything formal that has to be done to
confirm this?

Nigel

bussaca2@aol.com wrote:

> In a message dated 10/3/00 11:26:53 PM Eastern Daylight Time,
> legacy_productions@yahoo.com writes:
>
> > David
> >
> > I would be very interested in a rs style bumper for my 92 turbo
> > sedan,but only if I would beable to mount a pair of either the cibie
> > or PIAA driving lights in the factory locations(factory being for the
> > impreza).
>
> that is egzactly what i'm tring to do.. i personaly wouldn't settle for less.
>
> Living in northern Minnesota/Wisconsin requires me to drive
> > on very dark, very deer infested roads and I want some added light.
> > The rs bumper would only help, giving the lights a more finished look
> > and a meaner apperance.
> >
>
> I totaly agree. i put you on the list ,Unless you really icthing for them
> imediately I'm gonna wait till i got at least 5 other people who want the
> same thing to keep your costs down.
>
> David Carter
>
> To unsubscribe from this group, send an email to:
> BC-BFLegacyWorks-unsubscribe@egroups.com


To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

>I can afford to wait. (poor college student talking)
>Just tell me when you can get them.

Hey, cool. I'm not the only one then. =) I'm in, but like Jay said, I can
afford to wait. hehehe..

Jason
_________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.

Share information about yourself, create your own public profile at
http://profiles.msn.com.


To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com