Page 1 of 1
FS: TD05 with 90 degree inlet and early slant intercooler
Posted: Fri Sep 22, 2006 8:25 pm
by Matt Monson
I picked up a complete '96 swap this week. I don't need this turbo and intercooler, so I am selling it. It's got 65k mi on it and no shaft play. I will include ALL of the plumbing between the turbo and the intercooler, including the recirv vavle, as well as the two brackets (one bolts to the tranny and the other to the engine bellhousing) that hold the intercooler in place. I have it advertised elsewhere for $600. Special Leggy Central price for the old skoolers of $550.
The engine is also for sale, with a wiring harness, but without the ECU . PM me if you are looking for a 260hp EJ20G low mileage longblock and we can discuss. Asking price is $1000, without the above parts, $1400 with. I don't want to ship it, but willconsider it...
Posted: Fri Sep 22, 2006 9:00 pm
by 93Leg-c
Sending PM.
Posted: Mon Sep 25, 2006 6:44 pm
by Matt Monson
bizzump...
Posted: Tue Sep 26, 2006 12:27 am
by ultrasonic
Any chance you could post a couple photos of the i/c brackets? I'd like to fab up something similar when I install my slant i/c.
Good luck on the sale, sounds like a whole mess of fun for someone to get into.
Posted: Tue Sep 26, 2006 3:41 pm
by Matt Monson
Let me see what I can do. My camera has been on the fritz. I think it's time for a new digi...
Posted: Tue Oct 03, 2006 5:45 am
by bmxkelowna
whats the td05 from? the 96 jdm wrx?
td05 will bolt to the stock up/down pipes?
is the intercooler one of the small slant ones too?
Posted: Tue Oct 03, 2006 4:55 pm
by Matt Monson
Yes,
It's from the '96 WRX sedan. It will bolt right up to the stock up/downpipes and it is the small early 94-96 slanty intercooler...
Posted: Wed Oct 04, 2006 5:08 am
by bmxkelowna
TDO5-12A-8CM2 320 CFM
TDO5H-14B-6CM2 405 CFM
TDO5H-14G-8CM2 465 CFM
TDO5H-16G-7CM2 505 CFM
TDO5H-16G-10CM2 505 CFM
which td05 is it? do you know?
which injectors would be needed with the added flow, would stock 02 wrx ones work?
Posted: Wed Oct 04, 2006 1:03 pm
by rad rex
Any chance you want to sell just the IC Matt? If so how much?
Posted: Wed Oct 04, 2006 1:50 pm
by toomuch
another PM sent...
Posted: Wed Oct 04, 2006 3:52 pm
by Matt Monson
BMX,
I have the part number here with me at work. It is: 14412AA092 C9502-C9608
I will have to check the rest of the numbers on the housing to get you the rest of the information.
I do have a set of 440cc greytops available, along with Ej22e rails to install them into. $120 for the "kit"...
Rad Rex,
I will sell the IC seperately for $200, including all the plumbing and brackets...
Too Much,
back at you...
Posted: Wed Oct 04, 2006 4:27 pm
by rad rex
Matt, thanks but I''l pass
Posted: Wed Oct 04, 2006 8:59 pm
by Matt Monson
OK,
I want to add some clarity since I am getting a handful of PM's about stuff. If someone doesn't want the whole "kit" pricing is as follows:
Turbo only: $425
Intercooler only: $200 and for this price, you get the plubming from the turbo to the intercooler, BOV and mounting brackets. I will not sell the intercooler only.
Injectors and Fuel Rails for putting on an Ej22T: $120
And lastly, if you wanted the turbo, and the intercooler and the injectors with rails; the whole kit and caboodle is $650...
Posted: Thu Oct 05, 2006 1:03 am
by bmxkelowna
im interested in the turbo, intercooler and all the piping i would just like to figure out which td05 it is frist
Posted: Thu Oct 05, 2006 5:19 am
by Adam West
Hey this is cool. I'm just interested in the turbo since I already have an intercooler from an 06 WRX.
Does it come with all the necessary water lines, oil lines, banjo bolts and drain fittings?
I've heard some of that hardware is a be-atch to find and fabricate if you don't get with the turbo...Do I have that right?
Posted: Thu Oct 05, 2006 3:32 pm
by Matt Monson
Adam,
Yes, it has all of the coolant and oil lines with it, and they are included in the deal.
BMX,
I am considering your offer...
nice!
Posted: Thu Oct 05, 2006 9:47 pm
by andys2
I'm calling dibs!
I would like the turbo - assuming it's the 90 deg inlet. (425?) and the intercoolers intake pipe - the one that connects the turbo outlet to the intercooler inlet (50?).
Shipping is to Blaine WA. Give me your paypal and I will send you money. I also need it by tuesday
!
On another subject - can I put my EH25 phase1 heads on my ej20G block? One of my HLA heads is getting a bit suspect.
-Andy
Posted: Thu Oct 05, 2006 10:13 pm
by Matt Monson
Andy,
check you PM's...
Posted: Fri Oct 06, 2006 6:20 am
by bmxpunk
for clarity isn't that turbo the 16G matt? and damn it why didnt have that before??!!!?!?!
Posted: Fri Oct 06, 2006 4:06 pm
by Matt Monson
I'm pretty sure it's a 16g, but I am not really sure which one. The numbers on the turbo don't match up to the numbers posted above...
Sale is pending. I will update later today...
Posted: Fri Oct 06, 2006 9:38 pm
by Matt Monson
Turbo is SOLD.
Intercooler "kit" is still available. Price dropped to $150...