Thanks Mark I think I will look for some '96 n/a cams check them and
then use my factory roller solid adjustable rocker arms. I already
have a chip that works well.
Al(CO)
--- In BC-BFLegacyWorks@y..., Mark Ward <mark@r...> wrote:
> Be very carefull playing with cams on the motors. I believe there is
a
> reason not many companies sell cams. Your computer will adjust for
the cam.
> It would be better to gat a aftermaket computer then get a cam, or
even port
> and polish or get the roller rockerarms.
> If I am wrong, someone correct me...
> Mark
>
> -----Original Message-----
> From: milehial2000 [mailto:acroxford@h...]
> Sent: Tuesday, December 11, 2001 6:20 AM
> To: BC-BFLegacyWorks@y...
> Subject: [BC-BFLegacyWorks] Re: Cam question
>
>
> Sounds like you have the info. I guess what I am looking for is
specs
> on a good street cam for the turbo motor and thought that some of
the
> "hotter" versions of the Legacy motor might give me an idea as I
have
> heard several opinions on turbo cams. This all started when I
spotted
> a strange set of rocker arms on the shelf of one of the local yards.
> They had rollers and were mechanical non-hyd adjustable arms. The
> rollers are more "free hp" about 6 if I am right so I ran home
bolted
> them on set them at 8 and 10 for starters as adjustment info is not
> available started it up and it ran terrible. The roller arm geometry
> is different so the timing was off. Supposedly these arms came off
of
> a '96 engine so I guess I could try the '96 cam but now wonder if a
> reground cam might be worthwhile and what the gain might be.
> Al(CO)
>
>
>
>
>
>
> --- In BC-BFLegacyWorks@y..., Mark Ward <mark@r...> wrote:
> > What do you want? I have the complete spec on them (homolgation
> papers are
> > very detailed).
> >
> > EG:
> > Basic Circumfrence: 34.00 mm
> > Inlet lobe 39.5mm
> > Exhaust lobe 39.5mm
> > Timing:
> > Valve opens Inlet: 20 deg before btc Exhaust: 60 deg Before BDC
> > Valve closes Inlet 60 deg after BDC Exhaust: 20 deg After TDC
> >
> > Cam lift:
> > Inlet:
> > - 5 deg 5.5 mm
> > - 10 deg 5.3 mm
> > - 15 deg 5.0 mm
> > - 30 deg 3.5 mm
> > - 45 deg 1.2 mm
> > - 60 deg .3 mm
> > - 75 deg .1 mm
> > + 5 deg 5.5 mm
> > + 10 deg 5.3 mm
> > + 15 deg 5.0 mm
> > + 30 deg 3.3 mm
> > + 45 deg .8 mm
> > + 60 deg .3 mm
> > + 75 deg .2 mm
> > Etc...
> > Mark
> >
www.rrunracing.com
> >
> > -----Original Message-----
> > From: milehial2000 [mailto:acroxford@h...]
> > Sent: Monday, December 10, 2001 10:45 AM
> > To: BC-BFLegacyWorks@y...
> > Subject: [BC-BFLegacyWorks] Cam question
> >
> >
> > Does anyone have the complete specs on the EJ2.0t cams ? Any
> > information on them ?
> >
> >
> >
> > To unsubscribe from this group, please send an email to:
> > BC-BFLegacyWorks-unsubscribe@e...
> >
> >
> >
> > Your use of Yahoo! Groups is subject to
>
http://docs.yahoo.com/info/terms/
>
>
>
> To unsubscribe from this group, please send an email to:
> BC-BFLegacyWorks-unsubscribe@e...
>
>
>
> Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
------------------------ ---------------------~-->
Stop Smoking Now
Nicotrol will help
http://us.click.yahoo.com/2vN8tD/_pSDAA ... /XoTolB/TM
---------------------------------------------------------------------~->
To unsubscribe from this group, please send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com