How to read Check Engine Light Codes
Legacy Turbo ECU Pinout Diagram Needed
First Gen Turbo Legacy ECU I/O Spreadsheet
An ECU scan tool for turbo and NA owners
Alarm/Remote Starter wiring info UPDATE #2
My new project -- a standalone scan tool (lots of pictures)
Factory plug fix
THE EJ20G ECU Thread
How to read the codes from auto seatbelt computer
EJ20G "RobTune" Info
Rob's 4to2 Igntion Converter
3 wire to 2 wire alternator plug conversion info
Radio Wire Diagram
Behind Dash Relay Location Guide With Pictures!
Reading Electrical Connector Diagrams & Pin Numbering
Variable Intermittent Wiper Upgrade - DIY with pictures
How-To: Convert To GD WRX Coil On Plug w/EJ20G ECU
Apexi AVC-R install
Select Monitor or Scan Tool Check Sheet
Electronic Legacy gauge cluster into a US Legacy
Shielded Wire Replacement
Alternative ECU Patch/Test Harness Options
Reading Electrical Connector Diagrams & Pin Numbering
Electrical Compilation Thread Sticky
Moderators: Helpinators, Moderators
Electrical Compilation Thread Sticky
Josh
surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT
If you need to get a hold of me please email me rather then pm
surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT
If you need to get a hold of me please email me rather then pm
Great idea!! I refer to the engine forum on all the time.
Taking suggestions?
I seem to refer tons of folks from other forums to these two threads of mine. Maybe the sticky would be a good place to flag them?
"Need electronics help", the thread where we outlined if it was poosible to run a 4 channel ECU with the factory harness.
http://bbs.legacycentral.org/viewtopic.php?t=35093
And the eventual "how-to" thread. However, upon re-reading it, it could use some clarification. I'll try working on it if there is enough interest.
http://bbs.legacycentral.org/viewtopic.php?t=37071
Taking suggestions?
I seem to refer tons of folks from other forums to these two threads of mine. Maybe the sticky would be a good place to flag them?
"Need electronics help", the thread where we outlined if it was poosible to run a 4 channel ECU with the factory harness.
http://bbs.legacycentral.org/viewtopic.php?t=35093
And the eventual "how-to" thread. However, upon re-reading it, it could use some clarification. I'll try working on it if there is enough interest.
http://bbs.legacycentral.org/viewtopic.php?t=37071
'93 Winestone SS Auto, '91 Pearl White SS.
'93 Pure White SS EJ20G slanty intercooled, SIDESWIPED! In stasis.
'94 FWD and '95 AWD Laguna Blue SVXs.
2017 Pure Red BRZ Limited w/Performance pack
'93 Pure White SS EJ20G slanty intercooled, SIDESWIPED! In stasis.
'94 FWD and '95 AWD Laguna Blue SVXs.
2017 Pure Red BRZ Limited w/Performance pack
Let me know when you're happy with the threads, I will add to the sticky post.
Josh
surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT
If you need to get a hold of me please email me rather then pm
surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT
If you need to get a hold of me please email me rather then pm
-
- In Neutral
- Posts: 6
- Joined: Mon Mar 16, 2015 9:11 pm
Re: Electrical Compilation Thread Sticky
Perhaps SAFC settings and info would be good to add? Considering it's the most commonly used and easiest to operate air/fuel controller.
-
- Moderator
- Posts: 5000
- Joined: Tue Aug 25, 2009 7:52 am
- Location: Des Moines, Wa
Re: Electrical Compilation Thread Sticky
Hi GarageBuilt, I am not aware of any current members (besides yourself) who are using it. If you want to create a thread on the ins and outs, installation, tuning and results, I can ask the administrator if we can add it to the sticky.
1992 Legacy SS 5mt, build in progress
Josh Colombo wrote: ↑Mon Jan 14, 2002 10:23 am Wait....I'm confused now.